HPA replica MTW HPA system HPA Magazine | Electronics Battery Nozzle Parts | Stock Grip Dropstock | Regulator Hose Fittings
| Air tanks
Air systems |
AEG Replica
P6 Custom | Magazine Hop-Up Precision barrel Complete upper Stand | Mosfet AEG spring Trigger Motor
| Gearbox
| Body and Parts
Dropstock | Kriss Vector Zone Scorpion Zone AEP Zone PTW Zone Skins |
Gas & Co2 airsoft pistol Gas & Co2 airsoft rifles HOLSTER | Magazine
Magazine accessory Stand | Precision barrel Hop-up
Conversion kit | Pistol parts
AAP-01 Universe | GBBR rifle parts
RIS for M4 GBB Sling mount MWS Universe | Grenade launcher 40mm Grenade Grenade |
Sniper replica Magazine | Spring Precision barrel Hop-up Barrel spacer | Piston Spring guide Cylinder set Cylinder head | Trigger group Flash hider Outer barrel Upper Sniper | Cocking Handle Stock Rail Skins | SILVERBACK
VSR10 universe AAC T10 universe STRIKER universe |
SHOTGUN | Shotgun shell | Parts | Shell holder | Tank |
Stock Supressors
RIS System
| Front grips Front Rail Scopes and red dots
| Mount & accessories Iron Sights Sling Swivel Flashlights & Lasers | Communication Flash hider Gas block Magazine accessory | Magwell AN PEQ Tracer device Chrony | Case Tools Shooting target Bipod |
Battery & related
| Gas CO2 Skins | BBs BB loader | Maintenance Paint Light Stick | Battery Smoke grenade |
Gloves Slings Bags | Combat vest Face protection Googgles Powerbank | Ghillie Kneepad Helmet for roleplay Magazine holder | Team Armband Shemaghs Clothing BELT | Knife Cap / Beanie HOLSTER Pouch | Survival GPS Patchs Other |
Si vous souhaitez enregistrer votre configuration, vous devez d'abord vous connecter.
ConnexionMaple Leaf Super Macaron is a special developed bucking to be used in your AEG or SRS replica. This bucking is designed to adapt the maple leaf crazy jet barrels, which are considered VSR/GBB cut barrels, to be used in AEG hop-up systems. While AEG buckings typically require "windowed" or "bridged" barrels, the Maple Leaf Super Macaron series slide onto "open cut/bridgeless" barrels just as a VSR style bucking would, but with the appropriate outer diameter to accommodate AEG Hop-up chambers. The bucking is best used in conjunction with the Omega Hop-up Tensioner , and Crazy Jet Barrel to really maximize your range and rein in that left and right shot deviation!
This bucking will fit bridged as well as bridgeless barrels, so be sure that your hop up chamber is designed for AEG buckings before ordering, as most GBB/VSR guns are designed for the thicker GBB/VSR buckings.
Different degrees available for your setup, higher FPS rifles would like to use harder ones. However with colder weather you might want to step down 5 degree to avoid a stiff bucking. Harder buckings wear down less then the softer ones. Softer ones give more consistency in your shots but wear down quicker.
The degrees of the hop-up buckings mark their compatibility with guns of different muzzle energies or power levels. In general, you could say: the more powerful the gun, the higher the degree. The manufacturer recommends choosing the degree of your bucking as follows:
The Maple Leaf Macaron hop-up bucking is compatible with electric guns made with Tokyo Marui standards. Note, however, that the nub of the bucking is shaped a bit different, which means that the hop-up window of the inner barrel should be at least the size of the nub, which is around 4 mm or longer.
Hardness degree | 50 |
Maple Leaf is an airsoft accessories and parts manufacturer from Taiwan that makes some of the finest internal upgrade parts and accessories at affordable prices. Producing products for all platforms ranging from GBB pistols to bolt action sniper rifles, Maple Leaf has you covered!
Bonjour ce joint est-il compatible avec le scorpion evo 3 avec le ressort m95 et le block hop up maxx ?
Cordialement
Bonjour , oui il est parfaitement compatible .
Cordialement,
Bonjour,
ce hop up est-il parfaitement compatible avec un canon krytac 6.05 (LVOA-C) ?
Et qu'en est-il du MR hop de la même marque ?
Merci d'avance
Bonjour;
oui il sera parfaitement compatible avec votre canon, tandis que le MR aura un appui trop large par rapport à la fenêtre de votre canon.
Cordialement.
Bonjour
Compatible avec une M4 colt avec canon 200mm 6.02 ?
Bonjour;
oui, 100% compatible.
Cordialement.
La patte d'appui en forme de triangle n'empêche pas l'utilisation d'un tensioner plat ?
Le joint est livré avec un nub de quel type ?
Bonjour , non un tensioner plat n'est pas exclu , cependant nous vous conseillons vivement le tensioner OMEGA de la même marque .
Le joint est livré seul sans nub.
Cordialement .
Le tensioner permet d'améliorer l'appui sur le joint hop-up et donc la la trajectoire des billes. Nous vous invitons à contacter notre service technique par téléphone si vous souhaitez davantage de renseignements concernant le montage des systèmes hop-up.